In-Line or Tee Filter? Protecting Instruments, Regulators and Analyzers

DK-Lok V73 series in-line filter

A-Best Industrial Inc. Fittings, Valves, and Tubing |

Most regulator seats, analyzer valves and needle valve tips that fail early don't wear out. Something gets in them: weld slag, rust flakes, a sliver of tubing burr or a chunk of thread sealant. A small filter in the right spot stops that for a lot less than a new regulator.

Where a filter earns its keep

  • Upstream of regulators, where a particle on the seat causes creep and pressure drift
  • Ahead of analyzers and sample systems that can't tolerate dirt
  • On the supply to small orifices, metering valves and solenoids
  • After new piping or tubing work, where construction debris is most likely
  • On gas supply lines from cylinders and tube trailers

V73 in-line filters: set it and forget it

DK-Lok V73 in-line filters are compact with a large filter area, rated 3,000 psig. They're the right choice where the element rarely needs changing, such as clean instrument air or a protective filter that only catches the occasional particle. To change the element you take the filter out of the line, so put it where that's easy to do.

V76 tee filters: service it in place

DK-Lok V76 tee filters are rated 6,000 psig, and the element changes without removing the filter from the line. An optional bypass lets you sample or purge. Pick a tee filter for dirty service, high-pressure gas, or any spot where you expect to check the element on a schedule.

DK-Lok V76 series tee filter

Picking the element

DK-Lok elements come in 0.5, 2, 7, 15, 60 and 90 micron. Finer isn't always better. A fine element plugs faster and adds pressure drop, so go only as fine as the equipment downstream needs. A good rule of thumb: match the element to what the instrument or regulator maker recommends, and if there's no guidance, start coarser and go finer only if you keep finding particles.

Both series come in 316 stainless or brass bodies, rated to 400°F, with 1/8" to 1/2" DK-Lok tube or pipe ends. Ratings vary by size, material and end connection, so check the exact part number before you order.

Install it the right way

  • Mind the flow arrow. A filter installed backwards can collapse or blow out the element.
  • Flush new lines before you put the filter in, or the first blast of debris will plug it on day one.
  • Leave room to get a wrench on the body and, for a tee filter, to pull the element.
  • Make up the DK-Lok tube ends like any fitting: tube bottomed, nut marked, tightened per the DK-Lok catalog, and checked with a gap inspection gauge.

Changing an element safely

  1. Isolate the filter on both sides and bleed it to zero. Confirm with a gauge.
  2. Open the cap slowly and stand to the side.
  3. Look at what the old element caught. Metal chips or slag tell you something upstream needs attention.
  4. Replace gaskets or O-rings if the kit includes them, reassemble and pressurize per your site procedure.
  5. Apply Gator Leak Detector around the cap and both tube connections and watch for bubbles or foam. If something leaks, isolate and depressurize before you put a wrench on it. Never tighten a fitting under pressure.

Mixing with Swagelok or Parker?

DK-Lok tube fittings are 100% interchangeable and intermixable with Swagelok and Parker A-Lok for like size and material, per DK-Lok's ASTM F1387 test report (14 intermixed combinations, witnessed by TÜV Rheinland, "No failure observed") and the Parker A-Lok interchangeability letter. A DK-Lok filter drops into an existing line without changing the fittings around it.

Need a filter or elements?

A-Best Industrial Inc. Fittings, Valves, and Tubing stocks DK-Lok V73 and V76 filters and field assembly kits. Call 310-833-3353 or email sales@abesttube.com.